Differences

This shows you the differences between two versions of the page.

--- projecst:delta3dprinter:start [2013/10/02 17:44] – created zimmer62
+++ projecst:delta3dprinter:start [2025/09/08 18:28] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
+**__//''combine''//__**
 Delta 3d Printer
@@ Line 13: / Line 15: @@
   - Decide on additional Electronics
   - Other electronics needed
-     * Stepper motors
+     * <del>Stepper motors</del> These were supplied from Dean Piper from Muve
      * extruder heater(s)
      * power supply(s)
@@ Line 20: / Line 22: @@
 /18/2013.  Rumba and endstops ordered from reprapdiscount.
-We need to source the stepper motors and additional electronics.  Ask Mike about the cost of the steppers from sparkfun.com
+We need to source the <del>stepper motors</del> and additional electronics.  <del>Ask Mike about the cost of the steppers from sparkfun.com</del>
 /27/2013.  Rumba, endstops, wiring kit, arrived.
-There are 4 matching Nema 17 motors on the shapoko in the basement.  (3 on the machine and 1 spare)  I think these will work and we can take them and replace the motors on the shapoko with Nema 23's
+<del>There are 4 matching Nema 17 motors on the shapoko in the basement.  (3 on the machine and 1 spare)  I think these will work and we can take them and replace the motors on the shapoko with Nema 23's</del>
-Brent Morse also has offered up some stepper motors.  I also have a bunch of motors pulled from machines.  3 motors should be identical, it would be nice to have a total of 6 motors on hand.
+<del>Brent Morse also has offered up some stepper motors.  I also have a bunch of motors pulled from machines.  3 motors should be identical, it would be nice to have a total of 6 motors on hand.</del>
 I saw a video of a rostock with quick change heads, this one in particular was making a pancake.
@@ Line 36: / Line 38: @@
 /2/2013 The rumba kit is in, located near the laser cutter by the delta printer board
+{{:projecst:delta3dprinter:img_6874.jpg?direct&300|rumba board}}
+{{:projecst:delta3dprinter:img_6881.jpg?direct&300|sd card reader}}
+{{:projecst:delta3dprinter:img_6879.jpg?direct&300|heat sinks}}
+{{:projecst:delta3dprinter:img_6875.jpg?direct&300|wires}}
+{{:projecst:delta3dprinter:img_6878.jpg?direct&300|fan}}
+{{:projecst:delta3dprinter:img_6873.jpg?direct&300|end stops}}
+{{:projecst:delta3dprinter:img_6876.jpg?direct&300|temp sensors}}
+{{:projecst:delta3dprinter:img_6880.jpg?direct&300|pulleys}}
+{{:projecst:delta3dprinter:img_6882.jpg?direct&300|}}
+<del>I stole the heat sinks from this for the solidoode2 printer I have.  I've ordered replacements, they will be here by Thursday.</del> Heat sinks have been replaced and installed.
+I've also ordered and LCD screen hopefully it's easy to integrate with this board.
+A Half built rostock with motors, but not electronics was donated by Dean Piper from [[www.muve3d.net|Muve3d]]

Lansing Makers Network Wiki

User Tools

Differences