User Tools

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
zones:3d_printing_area [2014/11/06 09:33] – jfahner3zones:3d_printing_area [2016/01/28 13:29] (current) – Fixed some outdated info. wreality
Line 3: Line 3:
  
 ===About=== ===About===
-The 3D Printing Area is located on the top floor of Lansing Makers Network.+3D printers live here.
  
 ===Stewards=== ===Stewards===
-Zone Steward: [[user:tim:start|Tim Schmidt]]+Zone Steward: :ORPHANED:
  
 ===3D Printing Zone Tools / Equipment=== ===3D Printing Zone Tools / Equipment===
Line 39: Line 39:
   * Get the Makerfarm printing reliably   * Get the Makerfarm printing reliably
     * Progress: Hot end installed and tested.  Extruding works!     * Progress: Hot end installed and tested.  Extruding works!
-    * [[user:tim:start|Tim Schmidt]]: determine the offset between nozzle and bed leveling probe, and update the printer's wiki page. +      - Question: New hot end topped out at 206 degrees, is that a firmware issue? 
-    * [[user:tim:start|Tim Schmidt]]: configure and install updated firmware +    * Progress: Jerry Fahner: Longer (blue) probe arm installed, arm angles and offsets determined, firmware reflashed, test print completed. Standard MakerFarm thermister table used but seems to work OK. 
-    * [[user:tim:start|Tim Schmidt]]: test printing +    * FIXME (unclaimed): Some tuning needed with Y-stop. The test print caused chatter when homing Y. 
-    * FIXME (unclaimed): soak magma hotend in acetone - it's already disassembled and in the glass container.+    * FIXME (unclaimed): Fan over-cools hot end. A piece of tape on fan helped but a shroud is needed. Reversing fan may help. 
 +    * Progress: [[user:zimmer62:start|Joe Zimmerman]]: soaked magma hotend in acetone, cleaned with fire, polished and is soaking again in the glass container.
   * Refurbish the solidoodle 2 3D printer   * Refurbish the solidoodle 2 3D printer
     * Looking for someone to help with the completion of this project.     * Looking for someone to help with the completion of this project.
-    * Progress: Joe Zimmerman had a design for laser-cut base to contain power supply.  This design never worked out, at the moment the design was scrapped. A mount for the electronics, and LCD also needs to be created+    * Progress: [[user:zimmer62:start|Joe Zimmerman]] has started another design for laser-cut base to contain power supply, MEGA / Ramps, Solid State Relay, Terminal Block etc.  A mount for the electronics, and LCD also needs to be created, possibly into the front of the base.
     * FIXME (unclaimed): laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic?     * FIXME (unclaimed): laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic?
     * FIXME (unclaimed): install power supply, electronics, LCD     * FIXME (unclaimed): install power supply, electronics, LCD
     * FIXME (claimed): run motor and hotend wiring     * FIXME (claimed): run motor and hotend wiring
-       - A crimper and ends have been ordered and received to put new ends on the motors and existing wiring. +       - A crimper and ends to put new ends on the motors and existing wiring are at the space. 
-       - The fan will need a DC-DC power step down converter which is on hand, but needs to be set for 12volts+       - The fan will need a DC-DC power step down converter which is on hand at the space, but needs to be set for 12volts
     * FIXME (unclaimed): laser cut improved magnetic side walls     * FIXME (unclaimed): laser cut improved magnetic side walls
   * Build a [[https://wolfmanjm.github.io/wolfstock/ | Wolfstock]] extra-large Delta 3D printer   * Build a [[https://wolfmanjm.github.io/wolfstock/ | Wolfstock]] extra-large Delta 3D printer

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also, you acknowledge that you have read and understand our Privacy Policy. If you do not agree, please leave the website.

More information