Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
zones:3d_printing_area [2014/11/06 14:40]
jfahner3
zones:3d_printing_area [2017/04/05 00:38] (current)
Line 3: Line 3:
  
 ===About=== ===About===
-The 3D Printing Area is located on the top floor of Lansing Makers Network.+3D printers live here.
  
 ===Stewards=== ===Stewards===
-Zone Steward: ​[[user:tim:start|Tim Schmidt]]+Zone Steward: :ORPHANED:
  
 ===3D Printing Zone Tools / Equipment=== ===3D Printing Zone Tools / Equipment===
Line 39: Line 39:
   * Get the Makerfarm printing reliably   * Get the Makerfarm printing reliably
     * Progress: Hot end installed and tested. ​ Extruding works!     * Progress: Hot end installed and tested. ​ Extruding works!
-    * ProgressExtra long probe arms printed in case they are needed - laying near printer +      - QuestionNew hot end topped out at 206 degrees, is that a firmware issue? 
-    * [[user:tim:start|Tim Schmidt]]: determine the offset between nozzle and bed leveling ​probe, and update the printer'​s wiki page+    * ProgressJerry FahnerLonger (blue) ​probe arm installedarm angles ​and offsets determined, firmware reflashed, test print completed. Standard MakerFarm thermister table used but seems to work OK
-    * [[user:tim:start|Tim Schmidt]]: configure and install updated firmware +    * FIXME (unclaimed)Some tuning needed with Y-stop. The test print caused chatter when homing Y. 
-    * [[user:tim:start|Tim Schmidt]]: test printing +    * FIXME (unclaimed)Fan over-cools hot end. A piece of tape on fan helped but a shroud is needed. Reversing fan may help. 
-    * FIXME (unclaimed):​ soak magma hotend in acetone ​- it's already disassembled ​and in the glass container.+    * Progress: ​[[user:zimmer62:start|Joe Zimmerman]]: soaked ​magma hotend in acetone, cleaned with fire, polished ​and is soaking again in the glass container.
   * Refurbish the solidoodle 2 3D printer   * Refurbish the solidoodle 2 3D printer
     * Looking for someone to help with the completion of this project.     * Looking for someone to help with the completion of this project.
-    * Progress: Joe Zimmerman ​had a design for laser-cut base to contain power supply.  This design never worked outat the moment the design was scrapped. A mount for the electronics,​ and LCD also needs to be created+    * Progress: ​[[user:​zimmer62:​start|Joe Zimmerman]] has started another ​design for laser-cut base to contain power supply, ​MEGA / Ramps, Solid State Relay, Terminal Block etc A mount for the electronics,​ and LCD also needs to be created, possibly into the front of the base.
     * FIXME (unclaimed):​ laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic?     * FIXME (unclaimed):​ laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic?
     * FIXME (unclaimed):​ install power supply, electronics,​ LCD     * FIXME (unclaimed):​ install power supply, electronics,​ LCD
     * FIXME (claimed): run motor and hotend wiring     * FIXME (claimed): run motor and hotend wiring
-       - A crimper and ends have been ordered and received ​to put new ends on the motors and existing wiring. +       - A crimper and ends to put new ends on the motors and existing wiring ​are at the space
-       - The fan will need a DC-DC power step down converter which is on hand, but needs to be set for 12volts+       - The fan will need a DC-DC power step down converter which is on hand at the space, but needs to be set for 12volts
     * FIXME (unclaimed):​ laser cut improved magnetic side walls     * FIXME (unclaimed):​ laser cut improved magnetic side walls
   * Build a [[https://​wolfmanjm.github.io/​wolfstock/​ | Wolfstock]] extra-large Delta 3D printer   * Build a [[https://​wolfmanjm.github.io/​wolfstock/​ | Wolfstock]] extra-large Delta 3D printer