Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
zones:3d_printing_area [2014/10/27 02:39] tim |
zones:3d_printing_area [2017/04/05 00:38] (current) |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ===About=== | ===About=== | ||
| - | The 3D Printing Area is located on the top floor of Lansing Makers Network. | + | 3D printers live here. |
| ===Stewards=== | ===Stewards=== | ||
| - | Zone Steward: [[user:tim:start|Tim Schmidt]] | + | Zone Steward: :ORPHANED: |
| ===3D Printing Zone Tools / Equipment=== | ===3D Printing Zone Tools / Equipment=== | ||
| Line 26: | Line 26: | ||
| * organize group-purchase filament orders | * organize group-purchase filament orders | ||
| * establish a regular meeting schedule | * establish a regular meeting schedule | ||
| + | * establish LMN-purchased stock, which can be paid for per-print via Cura / Repetier cost estimation | ||
| + | * purchase / install fast-heating bed heaters on all printers: http://www.ebay.com/itm/like/191353869307?lpid=82 | ||
| + | * maintain two or more working 3D printers at all times. | ||
| ===Ongoing Projects=== | ===Ongoing Projects=== | ||
| + | * 3D print a buildlog.net laser cutter rotational axis: http://www.buildlog.net/blog/2011/04/open-source-rotational-adapter-part-1/ | ||
| + | * Progress: not started | ||
| + | * FIXME (unclaimed): download the assembly STEP file, and export each printed part into an STL http://www.buildlog.net/wiki/doku.php?id=rotational | ||
| + | * FIXME (unclaimed): print parts | ||
| + | * FIXME (unclaimed): assemble and install in laser, connect motor to electronics | ||
| + | * FIXME (unclaimed): modify laser cutter firmware for rotational axis | ||
| * Get the Makerfarm printing reliably | * Get the Makerfarm printing reliably | ||
| * Progress: Hot end installed and tested. Extruding works! | * Progress: Hot end installed and tested. Extruding works! | ||
| - | * [[user:tim:start|Tim Schmidt]]: determine the offset between nozzle and bed leveling probe, and update the printer's wiki page. | + | - Question: New hot end topped out at 206 degrees, is that a firmware issue? |
| - | * [[user:tim:start|Tim Schmidt]]: configure and install updated firmware | + | * Progress: Jerry Fahner: Longer (blue) probe arm installed, arm angles and offsets determined, firmware reflashed, test print completed. Standard MakerFarm thermister table used but seems to work OK. |
| - | * [[user:tim:start|Tim Schmidt]]: test printing | + | * FIXME (unclaimed): Some tuning needed with Y-stop. The test print caused chatter when homing Y. |
| - | * FIXME (unclaimed): soak magma hotend in acetone - it's already disassembled and in the glass container. | + | * FIXME (unclaimed): Fan over-cools hot end. A piece of tape on fan helped but a shroud is needed. Reversing fan may help. |
| - | * Refurbish the solidoodle 3D printer | + | * Progress: [[user:zimmer62:start|Joe Zimmerman]]: soaked magma hotend in acetone, cleaned with fire, polished and is soaking again in the glass container. |
| - | * Progress: Joe Zimmerman has design for laser-cut base to contain power supply, electronics, and LCD. | + | * Refurbish the solidoodle 2 3D printer |
| - | * FIXME (unclaimed): upload Joe's design to the wiki | + | * Looking for someone to help with the completion of this project. |
| + | * Progress: [[user:zimmer62:start|Joe Zimmerman]] has started another design for laser-cut base to contain power supply, MEGA / Ramps, Solid State Relay, Terminal Block etc. A mount for the electronics, and LCD also needs to be created, possibly into the front of the base. | ||
| * FIXME (unclaimed): laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic? | * FIXME (unclaimed): laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic? | ||
| * FIXME (unclaimed): install power supply, electronics, LCD | * FIXME (unclaimed): install power supply, electronics, LCD | ||
| - | * FIXME (unclaimed): run motor and hotend wiring | + | * FIXME (claimed): run motor and hotend wiring |
| + | - A crimper and ends to put new ends on the motors and existing wiring are at the space. | ||
| + | - The fan will need a DC-DC power step down converter which is on hand at the space, but needs to be set for 12volts | ||
| * FIXME (unclaimed): laser cut improved magnetic side walls | * FIXME (unclaimed): laser cut improved magnetic side walls | ||
| * Build a [[https://wolfmanjm.github.io/wolfstock/ | Wolfstock]] extra-large Delta 3D printer | * Build a [[https://wolfmanjm.github.io/wolfstock/ | Wolfstock]] extra-large Delta 3D printer | ||
| Line 48: | Line 60: | ||
| * Improve the frame of the Rostock by replacing it's MDF with aluminum extrusion. Some 3D printed parts may need to be replaced. | * Improve the frame of the Rostock by replacing it's MDF with aluminum extrusion. Some 3D printed parts may need to be replaced. | ||
| * Progress: establish bill of materials | * Progress: establish bill of materials | ||
| + | * FIXME (unclaimed): print http://www.thingiverse.com/thing:516447/ | ||