Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
zones:3d_printing_area [2014/11/06 14:33]
jfahner3
zones:3d_printing_area [2014/12/03 18:33]
jfahner3
Line 39: Line 39:
   * Get the Makerfarm printing reliably   * Get the Makerfarm printing reliably
     * Progress: Hot end installed and tested. ​ Extruding works!     * Progress: Hot end installed and tested. ​ Extruding works!
-    ​[[user:tim:start|Tim Schmidt]]: determine the offset between nozzle and bed leveling ​probe, and update the printer'​s wiki page+      - Question: New hot end topped out at 206 degrees, is that a firmware issue? 
-    * [[user:tim:start|Tim Schmidt]]: configure and install updated firmware +    ​ProgressJerry Fahner:Longer ​probe arm installedarm angles ​and offsets determined, firmware reflashed, test print completed
-    * [[user:tim:start|Tim Schmidt]]: test printing +    * FIXME (unclaimed)Some tuning needed with y-stop.  
-    * FIXME (unclaimed):​ soak magma hotend in acetone ​- it's already disassembled ​and in the glass container.+    * FIXME (unclaimed) ​Fan overcools hot end. A piece of tape on fan helped but a shroud is needed. 
 +    * Progress: ​[[user:zimmer62:start|Joe Zimmerman]]: soaked ​magma hotend in acetone, cleaned with fire, polished ​and is soaking again in the glass container.
   * Refurbish the solidoodle 2 3D printer   * Refurbish the solidoodle 2 3D printer
     * Looking for someone to help with the completion of this project.     * Looking for someone to help with the completion of this project.
-    * Progress: Joe Zimmerman ​had a design for laser-cut base to contain power supply.  This design never worked outat the moment the design was scrapped. A mount for the electronics,​ and LCD also needs to be created+    * Progress: ​[[user:​zimmer62:​start|Joe Zimmerman]] has started another ​design for laser-cut base to contain power supply, ​MEGA / Ramps, Solid State Relay, Terminal Block etc A mount for the electronics,​ and LCD also needs to be created, possibly into the front of the base.
     * FIXME (unclaimed):​ laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic?     * FIXME (unclaimed):​ laser cut a test to verify that the dimensions are correct, then laser cut the final version - ply? acrylic?
     * FIXME (unclaimed):​ install power supply, electronics,​ LCD     * FIXME (unclaimed):​ install power supply, electronics,​ LCD
     * FIXME (claimed): run motor and hotend wiring     * FIXME (claimed): run motor and hotend wiring
-       - A crimper and ends have been ordered and received ​to put new ends on the motors and existing wiring. +       - A crimper and ends to put new ends on the motors and existing wiring ​are at the space
-       - The fan will need a DC-DC power step down converter which is on hand, but needs to be set for 12volts+       - The fan will need a DC-DC power step down converter which is on hand at the space, but needs to be set for 12volts
     * FIXME (unclaimed):​ laser cut improved magnetic side walls     * FIXME (unclaimed):​ laser cut improved magnetic side walls
   * Build a [[https://​wolfmanjm.github.io/​wolfstock/​ | Wolfstock]] extra-large Delta 3D printer   * Build a [[https://​wolfmanjm.github.io/​wolfstock/​ | Wolfstock]] extra-large Delta 3D printer