Differences

This shows you the differences between two versions of the page.

--- user:zimmer62:projects:cherrypi-iii-build [2015/05/22 15:02]
zimmer62
+++ user:zimmer62:projects:cherrypi-iii-build [2017/04/05 00:38] (current)
@@ Line 1: / Line 1: @@
 I would like to build a Cherry Pi III "ish" delta printer.  I will use many of the parts and idea from [[http://forums.reprap.org/read.php?178,361141|this forum]].  And [[http://www.thingiverse.com/thing:344408|this thingiverse page]].
-   * 5/18/2015 Start of the Cherry Pi III project
+   * 5/22/2015
+     * Printed [[http://www.thingiverse.com/thing:126778|Airtripper Bowden Extruder BSP Edition]]
+       * [[http://youtu.be/ziopiy626Cs]] Here is a timelapse of these parts
+     * Printed 4x [[http://www.thingiverse.com/thing:487476|Mini V Wheel Carriage for OpenBuild Extrusions]]
+       * Chose to print 4, so I'd have a spare, and because it lined up nicely on the plate (probably a wasted part)
+     * Aluminum Extrusion, and Mini V-Wheel kits showed arrived from OpenBuild
+     * Tested AstroBox / AstroPrint.  My thoughts are to currently avoid this
+       * The setup and web ui were very nice.
+       * It doesn't support streaming video which is a deal breaker.
+       * It can talk to your machine from the cloud, no obvious way to turn that off
+       * Raspberry Pi camera is not supported
+   * 5/21/2015 Some parts started to arrive, such as stepper motors and some screws and nuts.
+   * 5/20/2015 3D printed parts for base.
+{{:user:zimmer62:projects:parts_as_of_may_20.jpg?direct&200|}}
+----
+   * 5/19/2015 Tried acetone vapor bath just fro the heck of it.
+{{:user:zimmer62:projects:spool_disk_2.jpg?direct&200|}}
+----
    * 5/18/2015 Disc's for spool printed.
-{{ :user:zimmer62:projects:spool_disk_1.jpg?direct&200|}}
 {{:user:zimmer62:projects:spool_disk_1.jpg?direct&200|}}
 ----
+   * 5/18/2015 Start of the Cherry Pi III project
+     * Ordered Many Many parts online most were sourced from eBay, Amazon, or openbuilds.com
-   * 5/19/2015 Tried acetone vapor bath just fro the heck of it.
-{{ :user:zimmer62:projects:spool_disk_2.jpg?direct&200|}}
 ----
-   * 5/20/2015 3D printed parts for base.
 Sourcing a few parts have been difficult
   * Magnetic balls
-  *   * http://www.magnet4less.com/ need to figure out what to order
+    * http://www.magnet4less.com/ need to figure out what to order
+Extruder:
 Tim recomended the [[http://www.thingiverse.com/thing:126778|Airtripper Bowden Extruder BSP Edition]]
-Many parts were sourced from eBay, Amazon, or openbuilds.com
 I like this [[http://www.thingiverse.com/thing:651472|Lightweight end effector plate for Delta]] But it would need various  modifications depending on what we attach to it.
@@ Line 26: / Line 42: @@
   * http://www.spiderbot.eu/en/technology/tss-three-sphere-system.html
+the adjustment you need to make for size of parts (once you have your Z correct) is the delta rod length. You can use Rich's M666 command for that. The formula is (measured length/specified length) x delta rod length = new delta rod length
+tips... fan motor not spinning
+If you rotate the magnets you will find a 'sweet spot' where they don't cause this issue. I had the same problem on the original Cherry Pi.
+----
+Slicing
+Andy: I use 0.3mm layer height and 33% in fill on virtually all my printed parts. The effector, which is the only ABS part, I print at 0.2mm layer height.
+I have been using slic3r with a .3mm layer height and a 20% infill.  I've been printing all parts in ABS
+----
+Notes:
+It appears a different size carriage will be needed for the v-slot extrusions:
+[[http://www.thingiverse.com/thing:487476|Mini V Wheel Carriage for OpenBuild Extrusions]]
+http://forums.reprap.org/read.php?178,361141,page=17 This page here has someones build log where we can see how it's assembled