Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
equipment:makerfarm-i3 [2015/08/26 13:47] zimmer62 |
equipment:makerfarm-i3 [2015/08/29 03:19] mflaga |
||
|---|---|---|---|
| Line 31: | Line 31: | ||
| * Octoprint: | * Octoprint: | ||
| * Already done: | * Already done: | ||
| - | * RaspberryPi, USB wifi adaptor, SD card have been gathered. | + | * RaspberryPi-B, USB wifi adaptor, SD card have been gathered and at MakerFarm |
| - | * Octo-Pi has been installed. | + | * apt-get, rasp-config and OctoPrint upgrades have been done. |
| - | * Networking | + | * changed default user/pw of R-Pi. |
| - | * Pi camera has been ordered | + | * set timezone |
| + | * set keyboard to PC104-US | ||
| + | * Network setup with static IP at 10.1.10.221, on WiFi | ||
| + | * Note, seems OctoPi has FUBAR'ed wlan0 auto setup. | ||
| + | * Setup Port foward for below on ComCast Router. | ||
| + | * 22180->80(HTTP) | ||
| + | * 22144->443(HTTPS) | ||
| + | * 22122->22(SSH) | ||
| + | * Note | ||
| + | * There is no DNS at the space, yet. | ||
| + | * ComCast is DHCP, and there is no DynDNS setup. So you just need to know. It does not change much. | ||
| + | * Octo-Pi has been installed, | ||
| + | * created users | ||
| + | * some Octo Admin's | ||
| + | * a LMN common user | ||
| + | * enabled Auto login by local network | ||
| + | * any internal 10.1.10.0/24 will auto login with access. | ||
| + | * Remote or outside will be view only, unless with user/pw. | ||
| + | * enabled auto connect | ||
| + | * Changed Web Page Host name to "LMN MakerFarm i3 Prues" | ||
| + | * Limited haproxy to maxconn of 2. only lets two web pages, as not to overload Pi. | ||
| + | * USB camera has been ordered. | ||
| + | * Currently is trying Pi-Cam, very slow. | ||
| * Still needs done: | * Still needs done: | ||
| - | * Setup network with static IP or DNS at the space | ||
| * 3D Print an enclosure for the pi | * 3D Print an enclosure for the pi | ||
| - | * Create a printer profile | + | * currently using a stock case. But a better custom case to attach to MakerFarm is desired. |
| - | * Add LMN account so people may use this to print | + | * Need to investigate slowing down the FPS. Too much for Pi FFMPEG |
| + | * Create a printer setup - Work In Progress... | ||
| + | * temperatures | ||
| + | * beginning and ending Gcode scripts | ||
| + | * auto bed leveling code | ||
| + | * Cura profile | ||
| + | * More ... | ||
| * Write instructions on how to connect and print | * Write instructions on how to connect and print | ||
| * Install and test Cura profiles so STL's can be sliced on the machine | * Install and test Cura profiles so STL's can be sliced on the machine | ||
| * Install Pi camera on machine which might include 3d printing an enclosure for the camera. | * Install Pi camera on machine which might include 3d printing an enclosure for the camera. | ||
| + | * Currently Duct tape and Wire is holding camera. | ||
| + | * Add LED/Lamp for Camera | ||
| + | * Drive it from Ramps either: | ||
| + | * in parallel to fans | ||
| + | * in parallel to Motors being energized | ||
| + | * Add a G-Code (there may already be one) and create OctoPrint Plug-In | ||
| + | * Considerations: | ||
| + | * LDAP authentication or equivalent for future https://github.com/foosel/OctoPrint/issues/594 | ||