Differences
This shows you the differences between two versions of the page.
|
equipment:lms-cnc-mill [2014/05/09 21:38] wreality |
equipment:lms-cnc-mill [2017/04/05 00:38] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ---- datatemplateentry equipment ---- | ||
| - | template : templates:equipment | ||
| - | picture : equipment:lmscncmill.jpg | ||
| - | zone : Machine Shop | ||
| - | name : CNC Mill | ||
| - | manufacturer : Little Machine Shop | ||
| - | model : LMS-3960 | ||
| - | manual : equipment:3960_mini_mil_lusers_guide.pdf | ||
| - | memberlevel : Full | ||
| - | owner : Carl Raymond | ||
| - | type : CNC Mill | ||
| - | status_ : Operational | ||
| - | |||
| - | ---- | ||
| - | |||
| - | ===Description=== | ||
| - | |||
| - | This mill is a CNC conversion of Little Machine Shop's High Torque Mini Mill. It also has the high speed spindle upgrade installed, doubling the max spindle speed to 5000 RPM. | ||
| - | |||
| - | ===Specifications=== | ||
| - | |||
| - | ^ End Milling Capacity | 0.6" (16 mm) | | ||
| - | ^ Face Milling Capacity | 1.2" (30 mm) | | ||
| - | ^ Drilling Capacity | 0.5" (13 mm) | | ||
| - | ^ Table Size | 18.1" x 4.7" (460 mm x 120 mm) | | ||
| - | ^ X-Axis Travel | 11.8" (300 mm) | | ||
| - | ^ Y-Axis Travel | 5.1" (130 mm) | | ||
| - | ^ Z-Axis Travel | 9.8" (250 mm) | | ||
| - | ^ Throat | 6.5" (165 mm) | | ||
| - | ^ Head Tilt | None | | ||
| - | ^ Spindle Taper | R8 | | ||
| - | ^ Spindle Motor | 0.67 hp (500 Watts) | | ||
| - | ^ Spindle Speed | 200 - 5000 RPM | | ||
| - | |||
| - | ===Safety Rules=== | ||
| - | In addition to the [[zones:Shop Safety Rules| standard shop safety rules]] for the machine shop: | ||
| - | * Do not make contact with the revolving cutter. | ||
| - | * Place a wooden pad or suitable cover over the table surface to protect it from possible damage. | ||
| - | * Use the buddy system when moving heavy attachments. | ||
| - | * Do not attempt to tighten arbor nuts using machine power. | ||
| - | * When installing or removing milling cutters, always hold them with a rag to prevent cutting your hands. | ||
| - | * While setting up work, install the cutter last to avoid being cut. | ||
| - | * Never adjust the workpiece or work mounting devices when the machine is operating | ||
| - | * Chips should be removed from the workpiece with an appropriate rake and a brush. | ||
| - | * Shut the machine off before making any adjustments or measurements. | ||
| - | * When using cutting oil, prevent splashing by using appropriate splash guards. Cutting oil on the floor can cause a slippery condition that could result in operator injury. | ||
| - | |||
| - | ===Contacts for training== | ||
| - | |||
| - | For training contact [[user:carlraymond:start|Carl Raymond]] or [[user:wreality:start|Brian Adams]] | ||
| - | |||
| - | ===Safety Training=== | ||
| - | Review the following: | ||
| - | * Review of machine and shop safety rules. | ||
| - | * Proper procedures for securing parts / stock. | ||
| - | * Proper installation of cutting bits/tools. | ||
| - | * Proper operation and control of machine. | ||
| - | * Location, operation, and effect of all machine emergency stops. | ||
| - | * Proper procedures for cleanup. | ||