(GCode created using the HeeksCNC Mach3 post processor) (Test program) N10 G61.1 (Feeds and Speeds set for machining Pine) N20 G10 L1 P16 R0.094 (tool change to 3/16 inch Carbide End Mill) N30 G43 H16 N40 T16 M06 N50 G17 G90 G20 N60 G00 Z0.1 S2500 M03 N70 G00 X0.4287 Y0.0548 N80 G00 Z0.0787 N90 G01 Z-0.13 F80 N100 G01 X0.4287 Y-0.0548 F11.81 N110 G01 X-0.4287 Y-0.0548 N120 G01 X-0.4287 Y0.0548 N130 G01 X0.4287 Y0.0548 N140 G01 X0.5537 Y0.1798 N150 G01 X0.5537 Y-0.1798 N160 G01 X-0.5537 Y-0.1798 N170 G01 X-0.5537 Y0.1798 N180 G01 X0.5537 Y0.1798 N190 G01 X0.6787 Y0.3048 N200 G01 X0.6787 Y-0.3048 N210 G01 X-0.6787 Y-0.3048 N220 G01 X-0.6787 Y0.3048 N230 G01 X0.6787 Y0.3048 N240 G01 X0.8037 Y0.4298 N250 G01 X0.8037 Y-0.4298 N260 G01 X-0.8037 Y-0.4298 N270 G01 X-0.8037 Y0.4298 N280 G01 X0.8037 Y0.4298 N290 G01 X0.9013 Y0.5548 N300 G02 X0.9125 Y0.5533 I0.001 J-0.0354 N310 G01 X0.9159 Y0.552 N320 G01 X0.9191 Y0.55 N330 G01 X0.9217 Y0.5477 N340 G01 X0.926 Y0.5419 N350 G01 X0.9282 Y0.5351 N360 G01 X0.9288 Y0.5274 N370 G01 X0.9288 Y-0.5274 N380 G02 X0.9217 Y-0.5477 I-0.025 J-0.0026 N390 G01 X0.9191 Y-0.55 N400 G01 X0.9159 Y-0.552 N410 G01 X0.9125 Y-0.5533 N420 G01 X0.909 Y-0.5542 N430 G01 X0.9013 Y-0.5548 N440 G01 X-0.9013 Y-0.5548 N450 G01 X-0.909 Y-0.5542 N460 G01 X-0.9125 Y-0.5533 N470 G01 X-0.9159 Y-0.552 N480 G02 X-0.924 Y-0.5451 I0.0108 J0.021 N490 G01 X-0.926 Y-0.5419 N500 G02 X-0.9288 Y-0.5274 I0.0286 J0.013 N510 G01 X-0.9288 Y0.5274 N520 G01 X-0.9282 Y0.5351 N530 G02 X-0.924 Y0.5451 I0.0225 J-0.0035 N540 G01 X-0.9217 Y0.5477 N550 G02 X-0.9125 Y0.5533 I0.016 J-0.0159 N560 G02 X-0.9013 Y0.5548 I0.0101 J-0.034 N570 G01 X0.9013 Y0.5548 N580 G00 Z0.1 N590 G00 Z0.1 N600 M02